Tetrachloroethylene (PCE)
Tetrachloroethylene, also called perchloroethylene or PERC, is a dense chlorinated solvent associated with dry cleaning, metal cleaning, chemical processing and contaminated-site remediation. It is not normally a fire hazard, but its neurotoxicity, cancer concerns, dense-vapor behavior and hazardous thermal decomposition require selective monitoring and ventilation.
What Is Tetrachloroethylene?
Tetrachloroethylene, also called perchloroethylene or PERC, is a dense chlorinated solvent associated with dry cleaning, metal cleaning, chemical processing and contaminated-site remediation. It is not normally a fire hazard, but its neurotoxicity, cancer concerns, dense-vapor behavior and hazardous thermal decomposition require selective monitoring and ventilation.
Core references used for this page: NIST Chemistry WebBook — Tetrachloroethylene; NIOSH Pocket Guide to Chemical Hazards; OSHA 1910.1000 — Air Contaminants.
Tetrachloroethylene at a Glance
Appearance and fire behavior
Colorless, dense liquid with a mild ether-like odor
Generally nonflammable under normal ambient conditions, but heat and fire can generate highly toxic decomposition products.
Exposure-limit context
OSHA Table Z-2: 100 ppm TWA, 200 ppm ceiling and specified 300 ppm peak. NIOSH recommends minimizing exposure because PCE is a potential occupational carcinogen; NIOSH IDLH: 150 ppm.
Properties That Affect Safety and Measurement
| Property | Value or description | Engineering significance |
|---|---|---|
| Formula | C2Cl4 | Identifies the target gas or atmospheric parameter. |
| CAS number | 127-18-4 | Useful for chemical records, SDS review and analytical methods. |
| Molecular weight | 165.83 g/mol | Supports engineering calculations but is not a complete detector-placement rule. |
| Boiling / phase behavior | About 121.1°C (250°F) | Important for cryogenic releases, frostbite and pressure control. |
| Relative gas density | About 5.7 relative to air | One dispersion input among release momentum, temperature, ventilation and geometry. |
| Appearance and odor | Colorless, dense liquid with a mild ether-like odor | Human senses cannot provide a quantified or automatic safety response. |
| Fire behavior | Generally nonflammable under normal ambient conditions, but heat and fire can generate highly toxic decomposition products. | Determines whether enrichment, oxidizing behavior or nonflammability must be addressed. |
| Exposure / threshold context | OSHA Table Z-2: 100 ppm TWA, 200 ppm ceiling and specified 300 ppm peak. NIOSH recommends minimizing exposure because PCE is a potential occupational carcinogen; NIOSH IDLH: 150 ppm. | Do not treat occupational limits, oxygen boundaries and alarm settings as interchangeable. |
Gas density alone is not sufficient to determine detector placement. Release point, gas temperature, process pressure, ventilation, air movement, room geometry, obstructions and worker location must all be considered.
Where Tetrachloroethylene Is Used or Released
Common sources and release points
- Degreasing, cleaning and vapor-degreaser equipment
- Dry cleaning or textile processing where applicable
- Chemical manufacture and solvent reclamation
- Laboratory extraction and analytical use
- Contaminated-soil or groundwater remediation
- Drums, tanks, waste containers, spills and process vents
Industries and applications
Applications determine whether the measurement objective is personnel protection, process control, purity, emissions management or leak location.
- Industrial solvent and cleaning
- Coatings, inks or adhesives
- Chemical manufacturing
- Laboratory and analytical use
- Process or environmental monitoring
- Industrial hygiene and leak investigation
Industrial solvent and cleaning
Review storage, transfer, process equipment, ventilation, occupied access and maintenance states for credible releases.
Coatings, inks or adhesives
Review storage, transfer, process equipment, ventilation, occupied access and maintenance states for credible releases.
Chemical manufacturing
Review storage, transfer, process equipment, ventilation, occupied access and maintenance states for credible releases.
Laboratory and analytical use
Review storage, transfer, process equipment, ventilation, occupied access and maintenance states for credible releases.
Process or environmental monitoring
Review storage, transfer, process equipment, ventilation, occupied access and maintenance states for credible releases.
Industrial hygiene and leak investigation
Review storage, transfer, process equipment, ventilation, occupied access and maintenance states for credible releases.
Understand How Vapor Exposure Develops
Evaporation and vapor pressure
Tetrachloroethylene can enter air from open containers, wet surfaces, spills, heated processes, coatings, cleaning and transfer operations. Temperature and exposed surface area can strongly change the release rate.
Inhalation and absorption
PCE depresses the central nervous system and repeated exposure raises liver, kidney, neurological and cancer concerns.
Fire or decomposition behavior
Generally nonflammable under normal ambient conditions, but heat and fire can generate highly toxic decomposition products. A separate %LEL channel may be needed where fire protection is the objective.
Mixture and measurement uncertainty
Workplace air often contains several VOCs. A broad-response instrument may show a signal without identifying the compound or proving the concentration of this specific vapor.
Primary Hazards of Tetrachloroethylene
People and atmosphere
- Dizziness, headache and central-nervous-system depression
- Liver and kidney toxicity concerns
- Cancer risk from repeated exposure
- Dense vapor accumulation below grade
- Skin defatting and irritation
- Phosgene and acid-gas formation near flames or hot work
Reactivity, materials and equipment
- Prevent contact with flames, hot metal and welding because toxic decomposition products can form.
- Use closed-loop dry-cleaning or solvent systems and verified local exhaust.
- Check seals, hoses and gaskets for chlorinated-solvent compatibility.
- Manage contaminated filters, still bottoms and waste as vapor sources.
Never enter an unknown atmosphere. Leave the affected area, contact trained emergency responders, use appropriate respiratory protection and follow the facility emergency plan.
Separate Exposure Limits, Alarm Settings and Instrument Ranges
OSHA Table Z-2: 100 ppm TWA, 200 ppm ceiling and specified 300 ppm peak. NIOSH recommends minimizing exposure because PCE is a potential occupational carcinogen; NIOSH IDLH: 150 ppm.
Compound-specific ppm
Used for occupational exposure or process concentration. TWA, STEL, ceiling and IDLH values have different time bases and regulatory meanings.
TVOC / PID screening
A broad-response value can reveal change or locate a source, but it does not identify the compound and depends on lamp, correction factor and mixture.
Alarm programming
Alarm settings depend on the gas, application, jurisdiction, instrument, applicable standards and site-specific risk assessment.
Define the Safety Function Before Selecting a Sensor
Questions to answer
- What containers, coatings, cleaners, tanks or processes can release the vapor?
- Is the objective compound-specific exposure, TVOC screening, process analysis or %LEL protection?
- What ranges, response times and environmental limits apply?
- Which alarms control ventilation, isolation, evacuation or process action?
- How will the complete system be bump tested, calibrated and documented?
Instrument terms are not interchangeable
- Gas sensor: the sensing element.
- Gas detector: sensor plus electronics, output and alarm functions.
- Gas monitor: continuous or portable instrument that may log or calculate exposure.
- Gas analyzer: measures composition, purity or process concentration.
- Leak detector: locates or indicates leakage and may not report area concentration.
How Tetrachloroethylene Vapor Is Measured
Photoionization detector (PID)
Ultraviolet photons ionize compounds whose ionization energy is below the lamp energy; the resulting current is related to vapor concentration.
Infrared / FTIR / photoacoustic
The instrument measures compound-specific infrared absorption in a cell or optical path.
Colorimetric or derivatization method
The vapor reacts with a treated medium or reagent to produce a measurable color or derivative.
Gas chromatography / laboratory analysis
A sample is separated into components before compound-specific detection and quantification.
Metal-oxide semiconductor (MOS)
A heated sensing surface changes resistance when exposed to reducing or oxidizing vapors.
Where Monitoring Points Should Be Installed
Priority locations
- Near credible tetrachloroethylene release points such as tanks, pumps, valves, mixers, transfer connections and process enclosures
- At worker breathing zones or representative occupied locations when occupational exposure is the objective
- At low points, trenches, sumps or floor-level zones where dense vapor may accumulate, while still checking airflow and release temperature
- At local exhaust capture points, room returns and ventilation dead zones identified by airflow review
- At storage cabinets, coating or cleaning stations, laboratories and waste-handling areas where containers may be opened
- At confined-space entry points and inside the space under the approved atmospheric-testing plan
Placement review checklist
- Release point and failure mode
- Gas temperature, pressure and jet direction
- Normal, standby and failed ventilation states
- Room geometry, pits, ceilings and connected voids
- Worker breathing zones, exits and rescue approach
- Sampling delay and maintenance access
Validate detector coverage against real operating modes. A high or low mounting rule based only on molecular weight is not an adequate design method.
Prove the Complete Monitoring System Works
Functional verification
- Inspect power, enclosure, inlet, filter, wiring and fault status.
- Apply the correct challenge gas or reference atmosphere.
- Confirm response, display, local alarm, relays and remote notification.
- Calibrate when required or when the functional check fails.
- Record results, sensor age, faults and corrective action.
When additional testing is needed
- After over-range exposure or a high-concentration solvent release
- After condensation, washdown, filter loading or solvent contamination
- After repair, relocation, power loss or ventilation changes
- After unexplained drift, failed alarms or pump-flow faults
- Before critical confined-space or emergency work
Control Releases Before Relying on Alarms
Engineering controls
- Leak-tight piping, compatible materials and suitable pressure relief
- Ventilation sized for credible normal and abnormal releases
- Remote isolation, shutdown and safe discharge routing
- Alarm interlocks that are tested as a complete cause-and-effect system
- Confined-space, hazardous-location, hot-work and chemical-handling procedures as applicable
Gas-specific emergency priorities
- Leave the affected area and warn others; do not investigate an unknown atmosphere without suitable training and equipment.
- Eliminate ignition sources only when this can be done remotely or without entering the release area.
- Isolate the source and start engineered ventilation under the facility emergency plan.
- Use appropriate chemical-resistant PPE and atmosphere-supplying respiratory protection for emergency entry as required by the hazard assessment.
- Verify the specific vapor, oxygen and flammability conditions before re-entry or returning equipment to service.
Common Causes of Delayed or Misleading Readings
Sampling system considerations
- Select sorbent media and sampling duration to prevent breakthrough at the expected concentration.
- Minimize condensation and adsorption in tubing, filters and sample manifolds.
- Use inert or compatible wetted materials and document pump flow and transport delay.
- Do not convert a mixed-VOC PID or TVOC reading into a compound-specific result without a validated method.
Environmental and cross-sensitivity review
Verify PID lamp energy, response factors, background VOCs, oxygen dependency, pressure, temperature, humidity, condensation, response time, sensor aging and cross-sensitivity. The complete installed instrument—not only the bare sensor—must meet the required safety function.
Practical Answers to Frequent Mistakes
“PERC is harmless because it is nonflammable.”
Its toxic and carcinogenic hazards remain significant.
“Dry-cleaning machines contain all vapor automatically.”
Door seals, maintenance, waste and transfer can release vapor.
“PID identifies PCE uniquely.”
Other chlorinated and aromatic VOCs can respond.
“Heavy vapor only matters at floor level.”
Air movement and warm equipment can transport vapor throughout a workspace.
Comparing Measurement Approaches
| Technology | Suitable use | Advantages | Limitations |
|---|---|---|---|
| Photoionization detector (PID) | Fast screening for Tetrachloroethylene when lamp energy and response factor are suitable. | Fast response, broad VOC sensitivity and useful portable screening capability. | PCE responds well to common 10.6 eV PID lamps, but TCE and other ionizable VOCs create similar signals. A PID does not identify the compound and must be interpreted against the actual mixture. |
| Infrared / FTIR / photoacoustic | Compound-specific fixed or extractive monitoring for Tetrachloroethylene. | Can provide direct compound-specific measurement and is not dependent on oxygen for the optical response. | Spectral overlap, water vapor, path length and the required low concentration need application-specific validation. |
| Colorimetric or derivatization method | Spot checks or task sampling where a validated Tetrachloroethylene-specific tube or badge is available. | Compound-focused spot checks or validated sampling methods can reach low concentrations. | Consumable media, humidity, temperature, reading technique and interfering chemicals can affect results. |
| Gas chromatography / laboratory analysis | Confirming Tetrachloroethylene identity and concentration in mixed solvent atmospheres. | High specificity and defensible identification in complex mixtures. | Sampling media, laboratory turnaround and desorption recovery must be controlled. |
| Metal-oxide semiconductor (MOS) | Broad leak or trend indication in controlled equipment. | Compact, economical and sensitive to many VOCs. | Selectivity is limited and chlorinated solvents may produce weak or unusual responses. |
Tetrachloroethylene FAQ
What does tetrachloroethylene smell like?
Odor descriptions vary and odor thresholds do not equal safe exposure limits. Smell must not be used as the primary warning method for Tetrachloroethylene.
Is tetrachloroethylene a VOC?
Tetrachloroethylene is commonly discussed as a volatile organic compound or solvent vapor because it can enter air readily under relevant use conditions.
Is tetrachloroethylene flammable?
Generally nonflammable under normal ambient conditions, but heat and fire can generate highly toxic decomposition products. Verify the current SDS and process conditions because temperature, pressure and mixture composition affect fire behavior.
Is tetrachloroethylene heavier than air?
The typical vapor-density reference is About 5.7 relative to air. Density is only one input; release momentum, temperature, ventilation and room geometry determine actual movement.
Can a PID detect tetrachloroethylene?
Fast response, broad VOC sensitivity and useful portable screening capability. PCE responds well to common 10.6 eV PID lamps, but TCE and other ionizable VOCs create similar signals. A PID does not identify the compound and must be interpreted against the actual mixture.
Which sensor is best for tetrachloroethylene?
The correct method depends on whether the goal is compound-specific exposure measurement, broad VOC screening, leak detection, process analysis or %LEL fire protection. No single sensor is best for every objective.
Where should tetrachloroethylene detectors be installed?
Place instruments from the release scenario, airflow, worker location, vapor behavior and required response time. Gas density alone is not sufficient to determine detector placement.
What measuring range should be used for tetrachloroethylene?
Select a range around the applicable exposure limit or process objective, expected background, credible release and required resolution. A %LEL range and a ppm exposure range serve different purposes.
How often should tetrachloroethylene detectors be calibrated?
Follow the instrument manufacturer, site procedure, applicable regulation and risk assessment. Bump testing proves response; calibration adjusts accuracy and should also follow failed tests, over-range events or contamination.
What should be done during a tetrachloroethylene leak?
Leave the affected area, prevent unprotected entry, contact trained emergency responders, isolate remotely if safe and follow the facility emergency plan.
Sources and Further Reading
Requirements and numerical values may differ by jurisdiction, standard, pressure, altitude, composition and test condition. Use the original sources and applicable local rules when designing a system.
- NIST Chemistry WebBook — Tetrachloroethylene
- NIOSH Pocket Guide to Chemical Hazards
- OSHA 1910.1000 — Air Contaminants
- U.S. EPA — Volatile Organic Compounds and Indoor Air Quality
- PubChem — Tetrachloroethylene
- OSHA 1910.134 — Respiratory Protection
Educational content only: This page does not replace emergency services, medical advice, a workplace risk assessment, applicable codes, manufacturer instructions or qualified engineering judgement.
Plan a Tetrachloroethylene Vapor Monitoring System
Share the solvent or process source, target concentration, other VOCs, temperature, humidity, ventilation, required response time, certifications and maintenance constraints.